CISCO 1921/K9 – Cisco ISR G2 1900 Series Router

Please urgently confirm that this Router CISCO1921/K9 has BGP ( Border Gateway Protocol ) .
YES, BGP is supported by about all Cisco Routers .

cisco 1921 CAN support Vwic2-2MFT-T1/E1 ?
YES .

The 1900 series routers which IOS supports IP SLA ?
The dedicated or SLAs router is used entirely for Cisco IOS IP SLA operations and is connected to the edge routers to simulate the customer network traffic. It is typically a cisco 1900, 2800, 2900, 3800, 3900 or 7200 Series Router .

I have a 1921 router. Using usb cable I can connect to the console but can not get the router into rommon mode. I saw a post for a 1941 router where you can remove the flash to get it into rommon mode, but the 1921 flash can not be removed. I am using Mac terminal and screen command but am not able to send break signal. would love to know if it ’ mho possible .
I think you can. The CF is “ hidden ” behind a dust cover. The slots are located at the BACK of the unit, to the bequeath. The back is where the ports and EHWIC slots are .

The trouble one ‘m running into is all the sample configs for Cisco 1921 sample working config for VDSL with a VA-DSL-A card, one ‘m finding are for much older code, i need it for a 1921 with version 15.2 ( 3 ) thyroxine .
Hi, I believe you have an EHWIC-VA-DSL-A wag installed on the C1921 device. The sample configuration for the like would be as follows, 1. Configure the Controller, 2. Configure the Ethernet interface & its sub-interface, 3. Configure the Dialer interface and as per you requirements, you can configure the Authentication, IP addressing etc .

If I purchased a Cisco ISR G2 router on Cisco IOS Software Release 15.0 ( 1 ) megabyte before the restriction was imposed, what should I do ? And should I need to upgrade my Cisco IOS Software ?
Assuming that you already have purchased the securityk9 package for encoding, you must purchase a HSEC-K9 license as a plain .

Why do I need to purchase the SEC-K9 license as a spare ?
If you purchase a Cisco ISR G2 chassis and late decide to turn on security features, you must buy a SEC-K9 license. The administrator must download the license to the router and follow the license installation instructions that come with the license to be able to use the security features on the router .

On the Cisco ISR G2 routers with the SEC-K9 license, what burrow count and performance throughput are available ?
The SEC-K9 permanent wave licenses apply to the Cisco 1900, 2900, and 3900 ISR G2 platforms ; these licenses limit all code burrow counts to 225 tunnels maximum for IP Security ( IPsec ), Secure Sockets Layer VPN ( SSL VPN ), a fasten time-division multiplexing ( TDM ) gateway, and secure Cisco Unified Border Element ( CUBE ) and 1000 tunnels for Transport Layer Security ( TLS ) sessions. The SEC-K9 license limits encrypted throughput to less than or equal to 85-Mbps unidirectional traffic in or out of the ISR G2 router, with a bidirectional total of 170 Mbps. This prerequisite applies for the Cisco 1900, 2900, and 3900 ISR G2 platforms .

Can I upgrade my CISCO1921/K9 to CISCO1921-SEC/K9 ? And how can I do it ?
Yes, you can upgrade it with L-SL-19-SEC-K9=.

What modules should I choose for my CISCO1921/K9 ?
look at this postpone. The mesa shows recommended modules for this router .

source : https://oanhthai.com
Category : Tutorial

Trả lời

Email của bạn sẽ không được hiển thị công khai.