How to Mount Photographs (with Pictures) – wikiHow

{“smallUrl”:”https:\/\/www.wikihow.com\/images\/thumb\/a\/aa\/Mount-Photographs-Step-1-Version-3.jpg\/v4-460px-Mount-Photographs-Step-1-Version-3.jpg”,”bigUrl”:”\/images\/thumb\/a\/aa\/Mount-Photographs-Step-1-Version-3.jpg\/aid1374114-v4-728px-Mount-Photographs-Step-1-Version-3.jpg”,”smallWidth”:460,”smallHeight”:258,”bigWidth”:728,”bigHeight”:409,”licensing”:”

1Choose the mounting board color and size. You can choose a size that leaves a border around the photo, or you can mount the photo on a board that is exactly the same size as the photo with no edges showing. You also have the option to use a mat which will place a border overtop of the photograph.[1]

• If you choose a mounting board with a border, carefully choose what color you want to show taking into account whether or not it matches the photograph.
• There are many options of board mounts to choose from, including but not limited to, Fotoflat, Foamex, Foamcore, Gatorboard and Colormount.

You can choose a size that leaves a edge around the photograph, or you can mount the photograph on a board that is precisely the same size as the photograph with no edges showing. You besides have the choice to use a mat which will place a border dominate of the photograph .

2 Cut and measure your print. Use a rule to measure the dimensions of your print. Remember that if you want to leave a margin, your photograph needs to be slenderly smaller than the mounting board. Cut your photograph to size accordingly .

ad

3Cut dry mount tissue. Dry mount tissue is a special adhesive paper designed to attach photos to mounting boards. Cut the tissue slightly smaller than the photo, about 1/8 inch (3 mm) smaller than the print on all sides, so the edges aren’t visible beneath it.[2]

• Using an acid-free dry mount tissue is recommended as an acid-based tissue might cause visible damage to your mounted photos in the years to come.

Dry mount tissue is a special adhesive material paper designed to attach photos to mounting boards. Cut the weave slenderly smaller than the photograph, about 1/8 edge ( 3 millimeter ) smaller than the print on all sides, so the edges are n’t visible below it .

4 Tack the tissue to the back of the photo. Using small pieces of clear magnetic tape, attach the dry saddle horse tissue to the back of your photograph at each corner. This will hold it in place while you start adhering the tissue at the center .

{“smallUrl”:”https:\/\/www.wikihow.com\/images\/thumb\/2\/24\/Mount-Photographs-Step-5-Version-3.jpg\/v4-460px-Mount-Photographs-Step-5-Version-3.jpg”,”bigUrl”:”\/images\/thumb\/2\/24\/Mount-Photographs-Step-5-Version-3.jpg\/aid1374114-v4-728px-Mount-Photographs-Step-5-Version-3.jpg”,”smallWidth”:460,”smallHeight”:258,”bigWidth”:728,”bigHeight”:409,”licensing”:”

5Warm an iron up to a low heat level. Too hot of an iron will damage your photo. You can also invest in a dry mounting press, although they tend to be more expensive.[3]
Too hot of an iron will damage your photograph. You can besides invest in a dry mounting bid, although they tend to be more expensive .

6Set the photo on the mount board. Clean the backside of your photograph leaving no traces of dust so it will stick to your board without fuss. Be sure the tissue is attached, and center the print on the mounting board.[4]
Clean the rear of your photograph leaving no traces of debris so it will stick to your control panel without fuss. Be certain the tissue is attached, and center the print on the mounting board .

7 Place a sheet of blotter paper on top of the photo. This is an significant tone as blotting paper composition will absorb overindulgence moisture from the iron and will keep your photograph from getting damp. The blotter newspaper should be the same size as the print and it goes right over your photograph when you ‘re ironing .

{“smallUrl”:”https:\/\/www.wikihow.com\/images\/thumb\/2\/21\/Mount-Photographs-Step-8-Version-3.jpg\/v4-460px-Mount-Photographs-Step-8-Version-3.jpg”,”bigUrl”:”\/images\/thumb\/2\/21\/Mount-Photographs-Step-8-Version-3.jpg\/aid1374114-v4-728px-Mount-Photographs-Step-8-Version-3.jpg”,”smallWidth”:460,”smallHeight”:258,”bigWidth”:728,”bigHeight”:409,”licensing”:”

8 Adhere the photo to the board. Press the iron down firm in the kernel of the photograph. Hold your cast-iron or dry climb weight-lift there for about 5 minutes then the heat warms up the photograph, dry backing tissue and mounting board. Pull the corners of the photograph up cautiously after the middle is securely attached to the mounting board and remove the tape before adhering the edges to the board .

9Slide the iron from the center to each edge. Practicing this step first with an old print may help you get used to the process to ensure no mistakes are made. Make sure your iron stays in contact with the blotter paper to avoid getting bubbles in the mounted photo. Press the iron firmly down on the edges of the photo under even pressure for 5 minutes at each location.[5]
Practicing this step beginning with an old print may help you get used to the process to ensure no mistakes are made. Make certain your iron stays in contact with the blotting paper paper to avoid getting bubbles in the mounted photograph. Press the iron firm down on the edges of the photograph under even pressure for 5 minutes at each location .

{“smallUrl”:”https:\/\/www.wikihow.com\/images\/thumb\/8\/8b\/Mount-Photographs-Step-10-Version-3.jpg\/v4-460px-Mount-Photographs-Step-10-Version-3.jpg”,”bigUrl”:”\/images\/thumb\/8\/8b\/Mount-Photographs-Step-10-Version-3.jpg\/aid1374114-v4-728px-Mount-Photographs-Step-10-Version-3.jpg”,”smallWidth”:460,”smallHeight”:259,”bigWidth”:728,”bigHeight”:410,”licensing”:”

10Trim the edges of the board. Place your mounted photo on top of a cutting board, and use a box cutter or X-Acto knife to trim the edges of your mount board. Lay your ruler over an edge of the photo while cutting so you cut in a straight line. Smooth the edges of your photo with a nail file when you’re finished trimming.[6]
Place your mount photograph on top of a cutting board, and use a box cutter or X-Acto knife to trim the edges of your mount dining table. Lay your ruler over an edge of the photograph while cutting so you cut in a straight lineage. Smooth the edges of your photograph with a collar file when you ‘re finished trim.